06-reference/transcripts

cnc kitchen this resin printer changed my mind transcript

2026-10-16

This is it—the new Formlabs Form Studio One, built to compete in the consumer and semi-professional photopolymer 3D printing market. It is almost as functional as the professional Form 4, but costs about four times less. And, honestly, it looks great. And can I mention that you can finally use your own resins without having to buy an open source license for $875, which is more expensive than a new machine itself. I'll be honest, I've never been a fan of photopolymer 3D printing because of the smell and mess. But for some reason, Studio One made me "get hooked" on the resin again. Let's find out more. Greetings to everyone. I'm Stefan, and welcome to CNC Kitchen. This video is sponsored by PCBWay. More about them later . There's no denying that photopolymer 3D printing is exciting. The level of detail that can be achieved is incredible. Parts have virtually the same strength in all directions without the usual problems with layer adhesion, and some special resins have amazing

[00:01:00] properties. But despite all the advantages, I always preferred printing on my filament printers whenever possible. I've tried photopolymer printing off and on over the past few years, but the smell, stickiness, and mess annoyed me more than the results pleased me. I've bought a few machines over the years and the situation has certainly improved with less smelly resins and more streamlined processes. Especially the latest machine I purchased, the Formlabs Form 4, made the whole process much more convenient. But the printer, along with the washing and polymerization station, costs over $5,000, and even the cheapest resin costs about $80 per liter. This puts it well beyond the amateur and even semi-professional market, especially when you can get a photopolymer printer for as little as $200 or $300. And the reason for this is quite simple. Most photopolymer printers today use MSLA, or mask stereolithography, and from a hardware perspective they are relatively simple. You have a UV light source, an LCD screen that

[00:02:01] only lets light through where the resin needs to harden, and a moving platform that is submerged in a tank of resin. No belts, complicated print heads, or fancy high-speed electronics. So it has always been difficult for my audience to justify having such an expensive photopolymer kit like the Form 4 when there are much more affordable, albeit less convenient, alternatives. And I think Formlabs realized that despite their very strong position in the professional 3D printing market, there is a huge market for makers who print miniatures, visual prototypes, and small mechanisms, and they could satisfy them if they were cheaper. The result is the Form Studio 1 for $699, the new Alpha resins starting at $29 per liter, and the Form Studio Wash and Cure for $199. All of these are significantly more affordable than the professional series, but have many features in common. For the sake of transparency: this kit was provided

[00:03:00] free of charge by Formlabs, but all opinions are my own. From the outside, the Studio 1 looks great thanks to its retro 90s design and transparent plastic panels that reveal the internal electronics. At the start of sales, a limited Founders Edition version is available in three additional colors, which can be purchased until November 30: aqua, turquoise, and purple. I have the turquoise version and I'm not sure if I made the wrong choice . Let me know what color you would choose. After this period, the Studio 1 will only be available in graphite. And, to be honest, I still really like him. There is a large touchscreen on the front for configuring the device and starting printing. The power supply is built into the case. You get Wi-Fi and LAN connectivity, and there's a port on the back for connecting a hood or Formlabs' proprietary VOC filter, which purifies the air coming out of the printer. The entire device feels very high quality, with all parts specially designed and injection molded to reduce the cost of mass production. The printer can

[00:04:00] be used completely offline via LAN or USB drive, or connected to the Formlabs cloud for convenience and remote monitoring. Let's take a look inside. The transparent front panel flips back and stays in any position at almost any angle . However, I noticed that the device does not have the lowest center of gravity. If you open the door too abruptly, the printer may start to wobble. I never tipped it over, but this is one of the few times where it's noticeable that many of the parts that used to be metal are now made of molded plastic. The Studio 1 has a print area of ​​200 by 125 by 235 mm, which gives it a 25 mm higher print height compared to the Form 4. In terms of resolution, it is also a step forward. The Studio 1 has a pixel size of 35 micrometers compared to 50 micrometers in the Form 4. Both devices use anti-aliasing to improve print quality in the X and Y planes. Other manufacturers prefer to advertise

[00:05:00] their devices in terms of thousands of pixels (K). Formlabs doesn't do this, but if you do the math, the Studio 1 comes out to around 5.7K, while competitors claim 8K or even 16K. However, screen resolution isn't always the only factor that determines the level of detail. The optics, which determine the parallelism of the screen light when it hits the resin, and the resin itself also play an important role here. Although the UV LED power is lower than in the Form 4, the Studio One still inherits many quality optical solutions. And, as we'll see later, Studio One is capable of creating truly impressive detail. Another thing it inherited from its “big brother” is a light processing unit with a special texture that allows air to pass under the resin bath and reduces suction forces when separating the print from the transparent film in the bath. The light processing unit also has a built-in heater that brings the resin to the optimal printing temperature. This

[00:06:00] helps achieve the proper viscosity and reactivity for reliable printing results. Inside is a camera with a small backlight for remote monitoring and automatic timelapses. Another notable detail is the force sensor on the Z axis; its data is used to automatically adjust the lifting and lowering speed depending on the resin and print geometry, and it can even alert you to debris in the tub or on the platform. The Z axis itself uses two linear guides and a trapezoidal lead screw. Some of you might be calling for a ball screw here , but the system seems to work quite well. After all, Formlabs uses the exact same design in the Form 4. And since the build platform is quite heavy, the lead screw nut must always have sufficient tension. By the way, about the working platform: it is conveniently fixed in place with a lever. There is one feature that I am very glad they carried over from the Form 4, which is the flexible work platform. As I mentioned, one of my biggest complaints about photopolymer printing is mess, and removing parts stuck to the bed is a

[00:07:00] big part of that problem. From a conventional platform, prints have to be scraped off, and once the parts, still covered in resin, come off, they often fly in all directions. The flexible platform has a thin sheet of stainless steel that is magnetized to the main part. Once the print is complete, you simply squeeze the two tabs, bending the sheet, and the parts separate, ideally immediately going into a wash bath. And honestly, it's one of the best features on the entire device. It is not included in the basic package, but the flexible platform package costs only $50 more. Considering that the flexible platform alone costs $135, this upgrade is worth every penny spent. Okay, a little story from life. Last winter, a friend of mine contacted me because he wanted to print some figurines on a photopolymer printer , but he didn't have his own equipment. And since my printer was having some problems at the time, I simply sent it to PCBWay. He uploaded the files, instantly received a cost estimate, and even a nice discount using my PCBWay CNCKitchen10 promo code

[00:08:00] . And in just a few days, the finished parts were on his doorstep. No one can have absolutely all the equipment. But PCBWay has it. So if you have a project that requires parts that you can't or simply don't want to manufacture yourself, PCBWay is your perfect solution. From 3D printing with polymers or metals to machining and sheet metal work—PCBWay does it all, often faster and much cheaper than you expect. When we develop a new product, we also use PCBWay to create prototypes, which allows us to make changes faster without spending a fortune. So try their services and get a nice discount with my promo code in the video description. Oh, and did I mention that PCBWay also makes printed circuit boards? Yes, it does , and they are of quite high quality. Thank you to PCBWay for sponsoring this video. Now let's go back to Studio One, because there is another feature that makes working with photopolymer much more convenient. This feature is an automatic

[00:09:01] photopolymer feeding system. You no longer need to manually pour resin into the tank, risking overfilling it or running out of material in the middle of a print. Instead, you simply insert the cartridge into the printer, open the vent, and the printer automatically feeds the material as needed. The printer also tracks photopolymer consumption and notifies you if there is not enough material left in the cartridge to complete the print. While technically you can drain the photopolymer back into the cartridge and clean the reservoir for a different type of resin, it is common to use a separate reservoir for each type. When you're done printing, you remove the tank, close it with the included lid , and store it until next time. This is definitely an additional expense, but at least it minimizes your contact with the liquid photopolymer. Fortunately, these accessories are now not as expensive as they used to be. The standard tank for Studio One costs $55, and the Tank Pro version costs $79. Both the cartridge and the reservoir have chips, so the printer knows what material you have installed and will warn you if you

[00:10:01] accidentally try to mix incompatible resins. All this information is also automatically fed back to the slicer. Slicing for photopolymer printing is algorithmically much simpler than for filament printing, as there is no need to calculate complex trajectories of the print head movement. Instead, you simply slice the model into layers. Where there is a part, the LCD transmits ultraviolet light to cure the resin. In all other places it blocks the light. This also means that a good slicer for photopolymer printing usually doesn't create better toolpaths or layer images, but simply prepares geometry better and adds quality support structures. Formlabs has always controlled the entire process, from printer and resin to slicer, and Studio One is no exception. Well, except for one important change, which we'll talk about later. With a Formlabs printer, you have to use their PreForm slicer, available for Windows and macOS, but at least it's free. So, without directly

[00:11:00] using ChiTuBox or Lychee Slicer. To be fair , you can add supports to your part in another slicer and import the finished models with supports into PreForm. In PreForm, you can import parts, place and orient them, add supports, create cavities, resin drain holes, and even apply textures to surfaces. Although it is better to use Bump Mesh for this, as it offers significantly more textures and is much more versatile. Sorry, but I don't regret this self-promotion. There are a bunch of settings to play around with, but to be honest , I mostly used auto- orientation and supports. The only time I really interfered was when I wanted to avoid placing the support on a certain surface. After that, it's worth checking the print for warnings, which you should take seriously, because if you ignore them like I did, you 'll get a failed print. Then you choose the resin, the layer height (in my case, usually 50 or 100 micrometers) and send the job to the printer. Studio One first pours resin into the tank as needed,

[00:12:00] mixes it and heats it up slightly, then starts printing. The first few layers are exposed for significantly longer to ensure they are securely adhered to the platform. This is also one of the reasons why resin parts are usually printed on supports and rafts , rather than directly on the platform. The extra exposure and default compression create something similar to the “elephant’s foot” you may know from filament printing. You can compensate for this with chamfers at the bottom of the part or with slicer settings, but it's still a bit difficult to get the perfect result. So, when you get it right , these details look just amazing. Once the initial adhesion layers are complete, printing becomes significantly faster. In fact, exposing each layer takes only a small fraction of the total time. Most of the time is spent smoothly raising and lowering the work platform. And here's something about MSLA resin printing that's often easy to forget. Print time is almost independent of the number of parts you print. One part prints in about the same amount of time as 100 parts if they

[00:13:00] all fit on the same platform and have the same height. This is significantly different from other 3D printing technologies, where a print head deposits plastic or a laser melts powder. The speed of the device depends mainly on the type of resin and the height of the layer. With the Alpha Gray and Clear resins I tested, I was getting about 40mm of print height per hour at a layer thickness of 100µm. Formlabs also offers Alpha Rapid Resin for rapid prototyping, which prints at speeds of around 90mm per hour at a standard layer thickness of 150µm and up to 130mm per hour at 250µm, which is already approaching the performance of FDM printing. These speeds are quite decent, and most of my prints were ready within 2-3 hours. But when comparing specifications, these speeds are slightly lower compared to competitors. Once the print is complete, the platform lifts up, allowing excess resin to slowly drain back into the reservoir. These prototyping resins

[00:14:01] have a fairly low viscosity, so falling drops can sometimes splatter the resin onto the inside of the lid. This is somewhat annoying and creates additional dirt. It is always a good idea to let as much resin as possible drain back into the tank before flushing, as you not only save material, but also slow down the saturation of the flushing solution, which will have to be replaced less often. One nice feature of Formlabs platforms is that they can be fixed at a 90° angle inside the tank for better resin drainage. Despite its convenience, I noticed a small flaw in the design. Sometimes the lever for opening the front cover can get caught on one of the protrusions on the flexible platform. This almost blocks the lid, making it very difficult to open again. This does n't always happen, but I've encountered this problem a few times when I was n't careful enough in setting up the platform. Formlabs says it is working to fix this issue. When most of the uncured resin

[00:15:00] drains off, the parts should be rinsed to remove residue from their surface. To do this, Formlabs has released a new Form Studio Wash + Cure station. Even with the bundle discount, the Form Wash V2 and Form Cure V2 for the Form 4 together cost almost $900. The studio version costs only $199. This was achieved by combining washing and polymerization in one device, simplifying control, switching to some manual operations, and removing the heater from the polymerization station. This last point is especially important for technical resins, as I showed in the previous video, but it's not as critical for the typical resins you 'll print on Studio One. Studio Wash + Cure is essentially a 10-liter plastic container filled with isopropyl alcohol, a parts basket, and a magnetic stirrer. With the help of a flexible platform, you transfer it all to a container for washing, hopefully without making a mess. The platform fits perfectly into the top of the basket, where it is securely fixed, preventing resin

[00:16:00] and solvent from splashing. Then you squeeze the latches and the parts usually fall right into the tub. If anything remains attached, you can use a small scraper to remove them. Next, you close the lid, set the timer, and turn on the device. The magnetic stirrer at the bottom begins to rotate, periodically changing direction to thoroughly rinse the printed products. After washing is complete, you lift the basket and hook it onto the edge of the container. You can then remove your products through the holes on the side. While these holes are convenient, they can also be quite annoying. When I was printing samples from the 100+ textures currently available in Bump Mesh, some small fragments slipped out through the side windows and blocked the rotor at the bottom. So I had to fish them out of the cloudy isopropyl alcohol. However, I was told that they are working on a solution to this problem. My basket is still 3D printed, probably SLS on one of Formlabs' own Fuse machines, but I'm told the final production version will be injection molded. I hope they will also smooth out the edges of the holes on the bottom,

[00:17:00] as the slightly rough texture of my SLS basket has scratched the still soft surfaces of some of my pieces. After washing, any isopropyl alcohol residue must be carefully removed to avoid an uneven surface finish. I usually use a hand-held pneumatic sprayer, which I can safely recommend if you don't have compressed air on hand. Just be sure to wear safety glasses and do it outdoors. When the wash is complete, you put the station into polymerization mode by removing the alcohol container and installing the turntable, which fits into the slot at the back. You then place your prints on the turntable and fully polymerize them for about 5 minutes. I usually leave the supports in until the polymerization is complete, although some people remove them earlier while they are still soft and easier to remove. But whenever you take them off, especially from larger, less complex parts, it brings incredible satisfaction. Sometimes the supports come off almost like Velcro, and even the sound is similar. Just be sure to wear gloves, because those tiny

[00:18:00] support tips can easily prick your finger. Believe me, I checked it. And that's it . This is, in fact, the entire process of creating a photopolymer print on Studio One. The level of detail that can be achieved still surprises and excites me every time, especially since I'm used to printing with filament. Smooth parts, like this N64 controller case, come out great: only barely noticeable steps are visible on flat surfaces, and even those almost disappear if you reduce the layer height to 50 micrometers. The miniatures look really impressive, and honestly, this is one of the best uses for such a machine. Prints at 100 micrometers already look great, but going to 50 micrometers reveals even finer details. I also printed a few parts for an optical project I'm working on. The fact that these fine-pitch, large-diameter threads worked perfectly on the first try is truly impressive and extremely useful for this kind of prototyping. Then I printed the 101 textures available in Bump Mesh on these samples, showing where they really belong—on the

[00:19:00] printed photopolymer parts. The amount of detail that can be obtained on such surfaces is impressive. This brings them to life or simply makes them look like high-quality injection-molded parts . What do you think? By the way, you can find high-resolution images for many of my prints on my website, linked below. One thing that I was particularly interested in and that I think is not discussed enough is the dimensional accuracy of photopolymer prints, but I just want to touch on it briefly. When looking at incredibly small details, it's easy to assume that photopolymer parts should match the original STL geometry perfectly, but they can also deform during printing and post-processing. And if we measure some linear dimensions, test threads, or test parts, the dimensions look very close to what they should be . There is actually a whole section for adjusting this shrinkage for each type of photopolymer. But when it comes to more complex details, it's not so simple. You can already see a slight bend on the top

[00:20:00] surface of the body of this N64 controller. So, I did a quick 3D scan, and it not only confirmed my observations, but also revealed some pretty serious deformation of the outer edges of the case. Perhaps this detail is the worst possible scenario . Different resin types, print orientation, supports, or post-processing methods can reduce warping, but the risk of warping will always remain. And to be clear, this is n't just a Studio One problem. Photopolymer printing is generally as prone to this as filament printing. It's just something to remember and pay attention to. Of course, if you print mostly figures or organic shapes, this probably won't bother you at all . Along with Form Studio One, Formlabs also introduced new Alpha resins. The price of Alpha fast resin starts at $29 per liter. Gray, white, black, and clear cost $36 per liter, and modeling resin costs $42. Formlabs claims these resins are stronger than regular ABS-type materials, although they are intended primarily for visual prototyping and form testing, and I

[00:21:00] have already accidentally broken one large part. If you need something really tough, there's also the Tough 1500 resin for $79, which is about half the price of before. This is definitely a step in the right direction . Previously, even the cheapest Formlabs resins cost from $80 per liter. But obviously, if you're offering a budget printer, you also need more affordable supplies. Alpha resins are still more expensive than many third-party alternatives, but I believe there are good reasons to consider them. First, Formlabs produces resin in their own facility in the US, which gives them direct control over the formulas. And when I first opened Studio One after printing, I immediately noticed one advantage, or rather, I didn't notice anything at all. You may think I'm sensitive, but I really can't stand the smell of tar. In the past, I've even had reactions to it in the form of a sore throat or a mild skin rash. But the Alpha gray and clear resins had almost no noticeable odor, and during my

[00:22:00] studio tests I had no problems working with them. The Formlabs website has a detailed article on resin safety if you want to learn more. Of course, a faint or no odor does not mean that the resin is harmless or that proper protection can be ignored. This just means that at least the resins I tested are not as aggressive as the ones I used before. I still strongly recommend wearing gloves, safety glasses, and ensuring proper ventilation. I also just opened a plastic bag of solid resin, and although I have n't printed with it yet, this material has a much stronger smell. So keep this in mind when working with technical resins. Another advantage, especially for technical users, is the documentation for the materials. Formlabs always publishes very detailed specifications for its resins, including mechanical, thermal properties, and even solvent compatibility. But perhaps the biggest advantage of using Formlabs' own resin is that it is perfectly tuned for their printers. During the entire

[00:23:01] testing period, I did not have a single failed print. I used automatic orientation and support almost exclusively, and the only details that went wrong were those where I ignored PreForm warnings. And this is something that many Formlabs users will probably recognize. If you stay within their ecosystem, printing usually goes extremely smoothly without the need to change anything significantly. It's not just the printer, post-processing equipment, and resin that have become cheaper. Accessories like printing platforms and resin tanks are now also much more affordable. But the feature that received the biggest price cut is definitely the open material mode . On other Formlabs printers, using proprietary resins requires a license that costs up to $5,000. That's a lot of money just for the opportunity to use third-party material. Studio One's open material mode is completely free, so you can experiment with third-party 405 nanometer resins to your heart's content. All you need is the Form Studio One

[00:24:01] Resin Tank Pro, which costs $79. This tank is designed to be more chemically inert, making it compatible with a wider range of materials. The disadvantage is that you lose the automatic resin supply. You will have to pour the resin into the tank manually and adjust the printing parameters yourself. I actually wanted to test this with the self-lubricating resin that was sent to me a while ago. Unfortunately, I'm out of time and the bottle is already 3 years old, so I'm not even sure if the material is still suitable. It will be interesting to see if Formlabs starts cannibalizing sales of its own Form 4 with the new Studio One. Because, as you've seen, a beginner can do almost everything the same as a much more expensive machine. Well, almost everything. At launch, only three Formlabs engineering resins have confirmed settings for Studio One. These are Tough 1500, Flexible 80A, and True Cast resin. You can use most others, but without confirmed settings, you should expect slower and potentially less

[00:25:00] reliable printing. And biocompatible resins are not supported at all . But this is n't just Formlabs' attempt to protect its professional printer business. If we look closely at the Form 4, we see a mixer in the reservoir, which is not present in the Studio One. This is especially useful for filled or highly viscous resins, particularly those materials that can significantly improve the mechanical and thermal properties of printed parts . But I can totally understand Form 4 users if they get mad about not being able to use cheap alpha resins on their machines, because I don't see any technical reasons for this, only commercial ones. After all, you sell the printer once, and resin is a consumable that provides a nice steady income. So, who should buy which device ? If you're a professional who regularly prints with specialized engineered resins, requires proven processes, or works with biocompatible materials, the Form 4 still has significant advantages. But if you're primarily printing miniatures, visual prototypes, or even

[00:26:00] functional parts in standard resins, I'd have a hard time justifying the Form 4's significantly higher price. For such tasks, the Studio One offers nearly the same convenience and print quality for a much lower price. And, to be honest, I wouldn't be surprised if a lot of professional users end up choosing Studio One too. I think entering the semi-professional market was a smart decision for Formlabs. Because while photopolymer printing has become much more convenient in recent years, few competitors can match the perfection of the Formlabs ecosystem. And it's not just the software, it's all the little thoughtful details: from the flexible platform and resin drain angle to the rotating platform storage compartment on the back of the Wash + Cure. And of course, just look at how good this setup looks. Formlabs clearly knows how to design a user-friendly workflow for resin 3D printing. And bringing that expertise into a much more affordable system could be just what convinces more makers to try photopolymer printing.

[00:27:00] If previously Elegoo, Creality, and especially HeyGears created problems for Formlabs, this time Formlabs is attacking competitors with price and, especially, convenience. Remember how I said at the beginning that I was never a real fan of photopolymer printing? Well, I've been working with Studio One for a few weeks now, and let me put it in German straight. I didn't start hating him again. And for me, that's actually a big compliment. I was particularly impressed by how enjoyable it was to work with the new resins and how smoothly the entire ecosystem worked. Does this mean I'll suddenly start printing with photopolymer every day? Most likely, no. For many tasks, my filament printers are still quite sufficient, and they save me from the solvents, consumables, and general mess that inevitably comes with photopolymer printing. But when I need very small parts or products that need to be strong regardless of the orientation when printed, I am much more likely to choose photopolymer than before. So while Studio One didn't completely turn me into a

[00:28:01] photopolymer printing fan, it definitely made me reconsider my attitude towards this resin. In the past, if one of my friends asked me if I should buy a photopolymer printer, I usually advised them not to . But with Studio One and Reverb Station, you can now get a nice, more user-friendly system for around $1,000 that I could really recommend. Let us know what you think about Studio One and what exactly is holding you back from getting started with photopolymer printing. Thank you all for watching. I hope you enjoyed watching this video. If you want to support my work, go to Patreon or become a member of the YouTube channel . Also check out other videos in my library. Hope to see you in the next issue. Goodbye and goodbye. Mhm.